In this article, we will show you how to install a motherboard. This is the first step in understanding the best way to set up computer parts for World PC Tech. The motherboard is connected one way or the other to each device that is in your computer.
It is evident that the motherboard is pre-configured with multiple slots into which devices can be connected. There are also jumpers and connectors that you must configure to work correctly.
Always keep the necessary documentation on hand always. To help us with this tutorial, we’ll be using the typical ATX motherboard, which is common to all mid-tower computer models.
1. Open the Case and Remove Motherboard Tray
The first step is opening the box. The process for opening it will differ based on the model of case you are using. For mid-towers, you’ll most likely need to take off an upper panel over the place where the motherboard is going to be.
Remove the two screws that are holding the panel to your computer. Slide it off. Place them in a secure position. If you own an older chassis, you might need remove all of the screws on the rear of the chassis. Then, take them out.
If your device has a motherboard tray , you’ll be required to remove it too. Certain cases come with removable motherboard traytrays to assist you in installing motherboard units properly. These trays are very helpful and make the process of the installation of your motherboard much simpler. If your motherboard has tray, you should be sure to take it off also.
2. Install your ATX Connector Plate as well align the Motherboard to Case
If you look over all the components included in your motherboard you’ll find that the motherboard came equipped with its own faceplate. This may be unusual since your case has the ATX face plate that is already in place. The issue here has to do with be related to possible incompatibility. The ATX faceplate could contain connectors that are arranged in a different arrangement than the one included with the case.
It’s recommended to make use of the face plate included from your motherboard. To replace the face plate of the computer case simply press the edges until the plate pops open. The new face plate is then snapped into place while making sure that the keyboard and mouse connectors with the side of the case in which your power supply is located.
3. Install Standoffs and Secure the Motherboard
The next step in understanding the best way to install the motherboard is to align it. The holes in the tray to be matched with holes of the motherboard. However, there’s more to this than that. The first step is to locate the holes for mounting in the tray or case that are in line with the holes that are on your motherboard.
After you’ve identified the holes, it’s now time to put in the standoffs. Standoffs are basically plastic or brass pegs which will be used to help support the motherboard once it is installed. Spacers or pegs are available in a variety of styles; some are made of brass, while some will be made of plastic. Make sure you know which ones you own. If they’re made of brass it is possible that you will require an hex tool of some type to set them up. Place the standoffs into the holes you have discovered earlier.
Once the standoffs are securely mounted now is the time to ensure that the motherboard is secured. The motherboard should be aligned with your tray or case, to ensure that you can clearly see the standoffs through their holes that match in the motherboard. Start from the middle of the motherboard and screw the motherboard into the tray, or to your case.
Once you’ve finished the clockwise process, continue attaching the screws to the mounting holes at every corner on the motherboard. As you will see, understanding how to correctly connect motherboards on your computer requires more than a couple of seconds! https://worldpctech.com/learning-guides/how-to-remove-gpu-from-motherboard/
4. Installing Critical Wires and Connectors
The next step to learn the best way to set up computer parts such as your motherboard is to connect crucial wires and connects. Even if your motherboard is installed physically doesn’t mean it’s able to connect to other components of your system.
It is necessary to connect essential cables and wires in order to complete the procedure. The first wires to connect are the ones hanging from your case, including hard drive power, reset, power as well as speaker cables. Check your manual to learn how to connect these wires into the appropriate slots inside the case.
The second cable is the one that delivers power to your motherboard The 20-pin ATX power cable from the power source. It is connected to the right slot on the motherboard. Newer models of computers, like the Pentium 4 could also come with an additional connector for 4 pins that is 12v from the power supply which must be connected to the motherboard too. Verify that all important wires are connected. If you had an removable tray, you are able to insert it back into the case now.
Conclusion
You’ve learned how to install a motherboard the fundamental component of your computer. As you can observe that it’s not an extremely difficult procedure–certainly not brain surgery. However, it is important to adhere to the steps correctly.
Additionally, make sure you read through your instructions prior to beginning the installation. It will inform you which jumpers you must make before you can begin installing. The settings can differ based on the motherboard you bought.
Building your own personal computer is a thrilling experience. Understanding how to set up the components of computers, such as a motherboard, is all about creating the foundation. More Info
